01 COA & batch testing

What the COA for pumpkin seed oil actually contains

Technical document 01 · Reviewed 2026-11-19 · Pumpkin Seed Oil

On this page
  1. Reading the certificate
  2. Fatty acid share versus oil mass
  3. Limit, result and the condition figures
  4. Why two good lots can differ
  5. Using an outside laboratory
  6. What to compare between suppliers

A lot of cold-pressed pumpkin seed oil is judged on two separate questions: is the fatty acid make-up the one that was bought, and is the oil in good condition. The certificate answers both when it reports the GC profile, free fatty acid, peroxide value, moisture, colour, metals and microbiology, each with a method and a limit. The catalog values below are the release gates; the COA is the record of one lot against them.

In one line

The linoleic and oleic figures describe the oil, the free fatty acid and peroxide value describe its condition, and a certificate needs both before the lot can be released.

Reading the certificate

Each line should let a second laboratory repeat the measurement: the parameter, the method and the limit, with the result in its own column. A bare “conforms” hides which test was run and what it found. A percentage with no method is difficult to compare across suppliers.

Release specification for cold-pressed pumpkin seed oil, CAS 8016-49-9
TestMethodLimitBasis
AppearanceVisualDark green to brownish-green; clear to slightly hazyOil as sold
IdentificationGC fatty acid profileConforms to the reference profileOil as sold
Linoleic acid (C18:2 n-6)GC-FID of fatty-acid methyl esters45.0–55.0% of total fatty acidsOil as sold
Oleic acid (C18:1 n-9)GC-FID of fatty-acid methyl esters25.0–35.0% of total fatty acidsOil as sold
Free fatty acidTitration as oleic acid≤0.50%Oil as sold
Peroxide valueAOCS Cd 8b-90 or ISO 3960≤5.0 meq O₂/kgOil as sold
MoistureKarl Fischer≤0.1%Oil as sold
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kgOil as sold
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absentOil as sold

The profile rows and the condition rows answer different questions. The first two percentages say what the oil is; the next three say how it has been handled. The GC row also needs the chromatogram, the column, the esterification route and the standard, because two C18 acids can be close enough to merge if the separation is poor.

Fatty acid share versus oil mass

GC results are normally normalised to the total fatty acid content, not to the weight of the bottle. That matters as soon as the figure is used for a label: 50% linoleic acid in the fatty acid fraction corresponds to about 47.5 g per 100 g of oil after the glycerol part is accounted for, because the acids are esterified to glycerol. A factor near 0.95 is usual; the certificate and the label should use the same convention.

The other numbers have their own conventions. FFA is a titration expressed as oleic acid and reports the unesterified fraction, not total acidity. PV is measured per kilogram of oil and covers hydroperoxides. Moisture is measured on the oil as sold. These are not interchangeable percentages, and a certificate that does not name the basis leaves room for a conversion mistake.

Limit, result and the condition figures

A limit is the boundary for release; a result is what the lot measured. They should never share a cell. If the result column simply repeats the range, the reader has learned the specification but nothing about the lot.

What the lot record should show for each test
TestLimitExpected record
Linoleic acid45.0–55.0% of total fatty acidsMeasured value, basis and chromatogram
Oleic acid25.0–35.0% of total fatty acidsMeasured value from the same run
Free fatty acid≤0.50%Measured value as oleic acid
Peroxide value≤5.0 meq O₂/kgMeasured value, method and test date
Moisture≤0.1%Measured value
Metals and microbiologyElement- and test-specificA result per element; counts and absence statements

FFA and PV are the two numbers that change most between release and use. A lot can pass the profile and still be a poor purchase if PV is close to the ceiling or FFA has risen. PV also falls as hydroperoxides decompose, so a lower figure is not automatically better; the test date and p-anisidine value give the fuller picture. p-AV is not in the catalog but is worth requesting when oxidation is the concern.

Why two good lots can differ

The fatty acid profile follows the seed. Variety, latitude and season shift the balance between linoleic and oleic acid, and a lot at the edge of one range is usually at the opposite edge of the other. The catalog window is deliberately wide enough to absorb that variation; a value near a limit is not a defect by itself.

Handling changes the condition numbers. Cracked or damp seed raises FFA before the press; heat, light and air raise PV afterwards. A cold-pressed oil is not refined, so FFA and colour pass into the bottle, and filtration removes sediment without undoing oxidation. Colour is the least numerical signal; a duller or browner tone can mean oxidation, a different press batch or simply a different seed, so it should prompt a look at the batch record rather than an automatic rejection. The lot code on the COA, the pack and the retained sample should be the same.

Using an outside laboratory

Outside testing is most useful when the supplier's certificate leaves a question open: a new source, a first import, a suspected blend or a disputed result. Rather than repeating every line, target the gap. A full GC-FID run with the chromatogram, column, standard and quantification limit addresses identity and profile. Sterol and tocopherol patterns address authenticity. FFA and PV by a named method address condition, with p-AV added if oxidation is the issue. Metals and pesticides address the seed source, and a PAH screen is prudent where the seed was dried with combustion gases.

Ask for the limit of quantification with any “not detected” statement; without it, the result describes the method, not the sample. Keep the sample chain intact: the laboratory should test the retained sample and identify the lot in its report. If a result is challenged, a joint retest aimed at the specific question is more useful than a second full panel.

What to compare between suppliers

Two certificates can quote the same linoleic acid and still describe different materials. Compare the basis, the condition of the oil, the authenticity evidence, the grade and the traceability, not just the headline percentage.

Five comparison points for pumpkin seed oil offers
PointAsk forWhy it matters
ProfileFull GC, basis and chromatogramA measured oil, not a copied range
FreshnessFFA and PV with test dateAn old lot can pass the profile
AuthenticitySterol and tocopherol resultsSunflower blends can pass the profile
GradeCold-press record and filtrationCold-pressed is not refined
TraceabilityLot code on COA, pack and retention sampleA certificate should belong to the lot

The catalog specification is on the pumpkin seed oil product page; the grade choice is on the grade page; the authenticity tests are on the identity page. The methods index explains the GC work, the quality page covers lot release, and the flaxseed oil powder product page shows the other side of the comparison.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation