02 Grade comparison

Fluid, deoiled or modified: choosing a lecithin grade

Technical document 02 · Reviewed 2026-11-19 · Lecithin

On this page
  1. Why the range exists
  2. Fluid, deoiled, carrier-supported and modified
  3. Handling the fluid and the powder
  4. Dose arithmetic for each grade
  5. Writing the grade specification
  6. When another grade is the wrong purchase

Lecithin is a family of products, and the grade is fixed by four choices: how much phospholipid the material carries, whether it is fluid or solid, which plant it came from, and whether it has been modified. The catalog grade is soy lecithin at ≥60% phospholipids and ≥60% acetone-insoluble matter, available as powder or fluid. Each choice changes the mass on the label and the allergen declaration.

In one line

The grade is the acetone-insoluble figure plus the form and the source; changing any one of them changes the dose weight and the allergen statement.

Why the range exists

Three commercial forces create the range. The first is oil: fluid lecithin retains much of the soybean oil, while a deoiled powder is mostly phosphatide. The second is handling: a capsule line wants a powder that flows, and an oil blend can take a viscous fluid. The third is function: hydrolysis or fractionation changes how the material behaves in water.

Source cuts across all three. Soy lecithin is the catalog material; sunflower lecithin is a different product with a different fatty acid pattern and a different allergen statement. The two are not interchangeable under a “lecithin” label.

The word “grade” should therefore be followed by at least two qualifiers — for example, “soy, 60%, powder” — before a supplier can quote it.

Fluid, deoiled, carrier-supported and modified

Lecithin forms in commercial use
FormAcetone-insoluble matterPhysical stateWhere it is usedWhat follows the choice
Fluid soy lecithinAbout 60–65%Viscous, oil presentEmulsifier, oil blendsMore grams per gram of phospholipid
Deoiled soy powder≥95%Free-flowing powderCapsules, dry blendsLess oil; lower mass per phospholipid dose
Carrier-supported powderCarrier plus 50–70% lecithin; AI lowerFree-flowing powderSticks, blendsCarrier is declared; AI is read on the powder
Hydrolysed lecithin≥56.0%More hydrophilic fluid or powderInstant powders, emulsionsHigher acid value; separate additive limits
PC-enriched fractionNot the basis of the gradePowder or waxy solidDeclared PC doseDifferent name, assay and label

The catalog sits in the 60% band and can be quoted as a fluid or a powder. A powder can be deoiled, in which case the AI figure runs far above 60%, or carrier-supported, in which case the carrier is part of the specification and the AI is read on the powder. The certificate and the carrier declaration decide which one is in the pack.

Hydrolysed lecithin is a fourth form. The enzyme treatment raises the acid value and improves water dispersibility, and the EU additive specification gives it its own AI minimum of 56.0% and an acid-value limit of 45. It is not the same material as hydrolysed protein, despite the shared word.

A PC-enriched product is a fifth form and a different purchase. The lecithin versus phosphatidylcholine comparison sets out the difference.

Handling the fluid and the powder

A fluid grade is dark and sticky, pours slowly when cold, and is usually warmed to move it. Warmth has a downside: it darkens the colour and accelerates hydrolysis, so the heater should be set and recorded rather than left on. A powder grade is hygroscopic, dusts, and cakes when the store is humid; it disperses in water but does not dissolve.

Flow is not a cosmetic property. A deoiled powder and a carrier-supported powder can pass the same mesh and still have different bulk densities, and a hopper that feeds one will bridge on the other. Put bulk density and flow on the specification for a powder, and say whether the figure is measured on the powder or on the lecithin.

Both forms dislike heat. A powder that has been stored warm can still flow and still carry a higher acid value than the certificate reported, because hydrolysis leaves no visible mark.

Dose arithmetic for each grade

Start with the label's declared ingredient. A lecithin claim is a claim on the mixture; a phospholipid claim is a claim on the phosphatide fraction; a PC claim is a claim on one class. Each needs a different divisor.

Suppose the label declares 300 mg phospholipids. At a 60% phospholipid figure the powder weight is 500 mg; at 70% it is about 429 mg; at 95% deoiled powder it is about 316 mg. Suppose it declares 100 mg PC: at 20% PC the lecithin weight is 500 mg, and at 90% PC it is about 111 mg. These are illustrations; the certificate figure is the divisor.

Carriers change the divisor again. A carrier-supported powder's lecithin percentage and its AI percentage are different numbers, and the label has to say which one the dose is built on.

Writing the grade specification

Write five blocks into the grade specification: identity (soy lecithin, CAS 8002-43-5, additive entry), composition (AI, phospholipids and the factor, class profile), condition (moisture, acid value, peroxide value), contaminants (metals, microbiology, residual solvent), and labelling (allergen, GMO, carrier). Add the form and the particle size for a powder.

Name the method and the basis next to each number, and do not carry a fluid limit across to a powder. The COA page shows the report; the identity page shows the profile checks.

When another grade is the wrong purchase

A PC claim above what lecithin carries needs the PC fraction, not more lecithin. A soy-free claim needs a different plant, not a lower percentage. A clear solution needs a different ingredient, because lecithin disperses and clouds. A label that says lecithin cannot be filled with a PC isolate without a new label.

The product page lists the catalog grade; the MOQ page lists the packs; the stability page covers storage for each form.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation