01 COA & batch testing

What the COA for flaxseed oil powder actually contains

Technical document 01 · Reviewed 2026-11-19 · Flaxseed Oil Powder

On this page
  1. The certificate as a test report
  2. Two bases: the powder and the oil
  3. Release limit, batch result and the oxidation arithmetic
  4. What moves between batches
  5. When an outside test earns its place
  6. Six lines that decide whether two quotations match

A certificate for microencapsulated flaxseed oil powder describes two materials in one: the oil inside the starch wall and the powder that carries it. It has to report alpha-linolenic acid (ALA) by GC, the oil load, moisture, peroxide value, p-anisidine value, the carrier, particle size, heavy metals and microbiology, each with a method and a release limit. The catalog specification is the gate; the batch COA is the record of what a particular lot measured.

In one line

A flaxseed oil powder certificate has to put the ALA result, the oil load and the oxidation values side by side, because no one of them describes the powder.

The certificate as a test report

A line is auditable when it answers what was measured, by which method and against which limit. A line without a method cannot be repeated elsewhere; a limit without a method cannot show what the lot passed. The basis matters as much as the number, because ALA can be reported on the powder or on the oil.

Identity, oil and oxidation limits · microencapsulated flaxseed oil powder 50% · CAS 8001-26-1
ParameterMethodRelease limitReported on
Alpha-linolenic acid (ALA, C18:3 n-3)GC-FID of fatty-acid methyl esters≥22.5%Powder as sold
Oil loadSolvent extraction or gravimetric50.0% declaredPowder as sold
MoistureKarl Fischer or loss on drying≤5.0%Powder as sold
Peroxide valueAOCS Cd 8b-90 or ISO 3960≤5.0 meq/kgExtracted oil
p-Anisidine valueAOCS Cd 18-90 or ISO 6885≤20.0Extracted oil
CarrierDeclaration; IR if disputedModified starch, declaredPowder as sold
Particle sizeSieve analysis≥95% through 40 meshPowder as sold
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kgPowder as sold
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absentPowder as sold

The GC line needs more than a percentage. ALA is one C18:3 among several: gamma-linolenic acid is also C18:3, and heat during refining can create cis and trans isomers around the same retention window. Name the column, the methyl-ester preparation, the standard and the integration, and attach the chromatogram. ISO 12966-2 and ISO 12966-4 are the usual references. A certificate that reports one C18:3 peak without showing the separation is reporting a family, not ALA.

Two bases: the powder and the oil

ALA is measured on the extracted oil and can be calculated onto the powder; oil load is measured on the powder as sold. The figures multiply. At 50.0% oil load and ALA ≥22.5%, the oil must contain at least 45.0% ALA, because 22.5 divided by 50 is 45 — the bottom of the normal range for flaxseed oil, which leaves some room for crop variation and encapsulation losses.

One gram of powder therefore carries 0.5 g of oil and at least 0.225 g of ALA; a 500 mg capsule carries about 112 mg. A label that says “flaxseed oil powder 500 mg” without the oil load and the ALA figure says nothing about the fatty acid being bought. The certificate should state the calculation and whether the result is on the powder as sold or on a dried basis.

Release limit, batch result and the oxidation arithmetic

The release limit is the acceptance boundary; the batch result is what the laboratory measured. Both belong on the page, in separate columns. A result column that repeats the specification range is a copy of the gate, not a measurement.

PV measures hydroperoxides, the first products of oxidation; p-AV measures the aldehydes that follow. They move in different directions: as hydroperoxides break down, PV can fall while p-AV rises. A lot can sit inside both limits, with PV near 5 meq/kg, and still be a poor choice for a stick pack stored warm for a year. TOTOX = 2PV + p-AV reaches 30 at the catalog ceilings; that is arithmetic on the limits, not a result for any lot.

Heavy metals work the same way. Individual results for lead, arsenic, cadmium and mercury are more useful than one line that says the panel passed, and microbiology should give counts and absence results rather than a single “conforms”. If a certificate gives only the conclusion, ask for the numbers.

What moves between batches

ALA moves with the seed. Flax varieties, growing region and crop year shift the fatty-acid profile, and a lot that only just clears the 22.5% floor has less headroom for the losses that follow. Oil load moves with the emulsion and the spray-drying yield: a powder formulated at 50% can measure below it if the oil is not fully retained, and the ALA result follows the oil load down even when the oil is unchanged.

Oxidation moves with time, heat and oxygen between pressing and encapsulation. A lot that left the drier clean can arrive with a higher PV if the pouch is not a barrier or if it sat warm in transit. Colour and odour are less quantitative and often more revealing: a darker tint, caking or a paint-like smell points to oxidation even when the ALA assay still passes.

When an outside test earns its place

Order an independent test for a new source, a first shipment into a regulated market, a disputed release or a label claim close to the limit. The useful panel is not a full repeat; it is what the certificate leaves open. Ask for GC-FID with the chromatogram, the column, the standard and a limit of quantification; PV and p-AV by a named method; the tocopherol profile and oil load by extraction; and ICP-MS for the metals. A “not detected” line without a limit is evidence about the method, not about the sample.

Six lines that decide whether two quotations match

Six lines that separate two flaxseed oil powder quotations with the same ALA figure
LineWhat to ask forWhat it separates
ALA basisThe result on the powder and on the extracted oilA measured powder from a diluted one
Oil loadMeasured or calculated, on the same lotA 50% powder from a 40% powder
GC detailColumn, standard, chromatogram and integrationALA from total C18:3
OxidationPV and p-AV, method and test dateA fresh oil from an aged one
Carrier and antioxidantName and level of eachA declared matrix from an unknown one
Lot traceLot code on COA, pack and retained sampleA real lot from a copied certificate

Two quotations that agree on ALA but differ on the other five are not describing the same powder. The catalog specification sits on the flaxseed oil powder product page; the form choice is on the grade page; the tests that separate ALA from other oils are on the identity page. The methods are described in the analytical methods index, and the certificate terms in the COA glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation