06 Identity & adulteration

How to prove a hemicellulase lot is what the name says

Technical document 06 · Reviewed 2026-11-20 · Hemicellulase

On this page
  1. Five layers of evidence
  2. Two ratios worth calculating
  3. What XRD can and cannot show
  4. Substitution modes and signals
  5. Identity lines for the specification
  6. Questions to put to the supplier

A hemicellulase lot is what the documents say it is only when several measurements agree: the declared activity on the named substrate, the protein behind that activity, the side-activity profile against a reference lot, and a lot code that links the powder to the paper. The class name is too broad to be proved by a single U/g figure, because a xylanase-dominant preparation, a mannanase-rich one and a blend can all return a plausible number.

In one line

Identity for a class name is a profile: the declared activity, the side activities and the source have to agree, and the lot code has to tie them to the pack.

Five layers of evidence

A certificate can carry the right product name and still fail to prove the material. The layers below run from paperwork to measurement to traceability, and a supplier who answers only the first has repeated the label rather than demonstrated the powder.

Five layers of hemicellulase identity
LayerQuestion it answersEvidenceWhat it establishes
PaperAre the product, source and CAS number named?Name, CAS 9025-56-3, production organism and strainDocumentation only
RateDoes it cut the declared substrate?Reducing-sugar assay with the stated conditionsThe declared activity
ProteinIs the rate carried by protein?Protein content and specific activityNot a spiked reducing sugar
ProfileWhat else is present?Xylanase, mannanase, arabinase, cellulase and protease resultsA side activity or a blend
ChainDoes the paper match the pack?Lot code on certificate, pouch or drum, and retention sampleTraceability

Two ratios worth calculating

The first is specific activity: units per gram divided by protein per gram, which gives units per milligram of protein. A dilution pulls both numbers down together, so the quotient holds while the strength of the powder falls. A cut with high activity and little protein looks like a purified fraction; a normal activity sitting on a large protein figure suggests inactive protein, fermentation solids or a different recovery point. The quotient is only meaningful inside one assay and one protein method, but across lots of the same product it is a steady check.

The second is the profile ratio, in particular xylanase against the declared hemicellulase activity. Xylan is the main hemicellulose, so a preparation with no measurable xylanase on a sensitive xylan assay is unusual; it usually means the product is mannanase- or arabinase-rich rather than defective. At the other end, a powder whose activity is almost entirely xylanase is a xylanase-dominant material sold under the broader name, which is legitimate when the profile is on the certificate.

Neither quotient is a purity percentage. Together they show that activity and protein move together and that the preparation still resembles the reference lot. The COA page shows where these figures belong on the certificate; the hemicellulase versus xylanase comparison explains why the two units are measured separately.

What XRD can and cannot show

An enzyme powder is amorphous, so an X-ray diffractogram of it is a broad halo. The technique cannot name hemicellulase, point to the production organism or measure activity, and a sharp reflection in a commercial powder is more likely to come from a crystalline carrier or a mineral contaminant than from the protein. Protein crystallography needs a single crystal, not a blended drum.

The narrower question is still worth asking. If a lot is disputed over its carrier or over an inorganic filler, XRD can show whether a crystalline phase is present and whether it matches the declared carrier. For identity, though, the evidence is the activity assay with its blank and standard curve, the protein figure and the profile against a reference lot.

Substitution modes and signals

Common hemicellulase substitutions and the signals
ModeHow it presentsWhat catches it
Dilution with carrierNormal-looking powder, lower U/g than declaredActivity and protein both low, specific activity steady
Reducing sugar addedAssay reads high while protein stays normalBlank, sugar screen, specific activity
Xylanase sold as hemicellulasePlausible U/g, profile almost entirely xylanaseMannanase and arabinase below the expected level
Different enzyme substitutedU/g plausible, process behaviour wrongProfile, protein pattern, substrate fit
Heat-inactivated materialAppearance right, activity lowActivity against a reference lot, protein normal
Carrier changed without noticeSpecification sheet unchangedCarrier identity, change-control record
Wrong lot shippedCertificate belongs to another containerLot code on pack, certificate and retention sample

Two of these modes pull in opposite directions: dilution lowers the activity, while added reducing sugar raises the assay reading. Running activity and protein on the same sample separates them. A 50,000 U/g powder with 2% protein and a 50,000 U/g powder with 10% protein are different materials even though the activity line reads the same.

Identity lines for the specification

A testable identity section names the product, the CAS number and the production organism, then the declared activity with substrate, calibrant, pH, temperature, incubation time and basis. It adds the protein or specific-activity range where agreed, the side activities that matter for the process, loss on drying, particle size, the carrier and the lot-code rule. The intended use belongs there too, because it decides which regulatory file applies.

  • “Hemicellulase, CAS 9025-56-3, produced by the named organism and strain.”
  • “Activity ≥50,000 U/g, with substrate, calibrant, pH, temperature, time and basis stated.”
  • “Side activities — xylanase, mannanase, arabinase, cellulase — each by its own method.”
  • “Protein or specific activity reported; carrier identity and ratio declared.”
  • “Lot code on certificate, pack and retention sample; identity test applied to every lot.”

Two habits make identity routine. State which identity test each new lot receives — the strain statement, the profile against a reference lot, or both — and keep the unit definition in a method appendix under change control, since a change of substrate or conditions makes two U/g figures incomparable.

Questions to put to the supplier

  1. Which organism and strain produced this lot, and is it the source used for the reference lot?
  2. What exactly is the unit: substrate, calibrant, pH, temperature, incubation time and mass basis?
  3. What are the xylanase, mannanase, arabinase and cellulase results, each by its own method?
  4. What are the activity and protein figures for this lot, and what specific activity do they give?
  5. Which lot code connects the certificate to the pouch, the drum and the retention sample?

Five direct answers amount to an identity file; one activity number does not. The product hub carries the catalog specification; the grades page compares the forms; the xylanase page is the single-enzyme comparison; the methods library explains the assay vocabulary; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation