02.1 Serine vs glycine

L-serine vs glycine: one hydroxymethyl group

Technical document 02.1 · Reviewed 2026-11-19 · L-Serine

On this page
  1. One carbon, one oxygen, two molecules
  2. The 30.03 g/mol difference on the balance
  3. Two assay methods, two specifications
  4. IR, HPLC and the mass that separates them
  5. Two names, two ingredients
  6. When to choose which

L-serine and glycine differ by one hydroxymethyl group: serine is C3H7NO3, 105.09 g/mol, and glycine is C2H5NO2, 75.07 g/mol. The 30.03 g/mol difference changes the assay method, the identity tests and the label. Glycine is achiral; L-serine has one stereocentre and a specific rotation. The two are separate ingredients and cannot be substituted by weight.

In one line

One hydroxymethyl group separates the two molecules, and it changes the molecular weight, the assay method, the identity test and the label.

One carbon, one oxygen, two molecules

Glycine is the smallest amino acid: an amino group and a carboxyl group on the same carbon, with two hydrogen atoms filling the rest of that carbon. Serine keeps the same backbone and replaces one of those hydrogen atoms with a hydroxymethyl group, -CH2OH. The change is small on paper, but it makes the two separate specification items with separate CAS numbers.

L-serine and glycine · structure and constants
PropertyL-serineGlycine
CAS number56-45-156-40-6
FormulaC3H7NO3C2H5NO2
Molecular weight105.0975.07
Side chain-CH2OH-H
IUPAC name(2S)-2-amino-3-hydroxypropanoic acid2-aminoacetic acid
ChiralityOne stereocentre; L formAchiral
pKa (carboxyl / amino)About 2.2 / 9.2About 2.3 / 9.6
Isoelectric point5.685.97
Nitrogen content13.33%18.66%

The isoelectric points are close, so pH is not a way to tell the two apart. Nitrogen content differs by about 5.3 percentage points, and the molecular weight differs by 30 units, which LC-MS sees at a glance. Both are white crystalline powders and both dissolve freely in water, which is why the certificate has to name the molecule and not only the appearance.

The 30.03 g/mol difference on the balance

The molecular-weight ratio is 105.09 ÷ 75.07 = 1.400. On a molar basis, 1 g of L-serine is 9.52 mmol and 1 g of glycine is 13.32 mmol. To replace 1 g of L-serine with glycine at the same molar amount, use 0.714 g; to replace 1 g of glycine with L-serine, use 1.400 g. Neither figure is a recommendation; it is the arithmetic that keeps a formula and a label in agreement.

Assay correction comes on top. A 99.0% dried assay with 0.3% loss on drying is 98.7% as-is, so the weighed amount is divided by 0.987 before any molar conversion. Apply both steps or the two errors compound. The assay basis is not a rounding detail when the dose is low and the capsule fill is tight.

A label that declares 1 g of L-serine is not satisfied by 1 g of glycine. At the same mass the glycine amount is 40% higher in moles, and the ingredient is different. The reverse substitution also changes the mass and the declared ingredient. The balance, the label and the certificate should use the same molecule, the same salt or free form and the same basis.

Two assay methods, two specifications

Glycine is assayed by titration on the dried basis. The catalog range is 98.5–101.5%, with loss on drying ≤0.2%, chloride ≤0.1% and residue on ignition ≤0.1%. L-serine is assayed by HPLC on the dried basis at 98.5–101.5%, with loss on drying ≤0.5% and pH 5.0–7.0. The methods are not interchangeable: a titration that counts acid and amino groups cannot distinguish glycine from serine, and an HPLC method that has not resolved the two peaks cannot prove either.

Neither molecule has a strong ultraviolet chromophore at conventional wavelengths. The serine method usually needs derivatisation or a low-wavelength detector, and the certificate should name the chemistry. Glycine's titration is a total acid-base measurement: it is a good assay for a pure lot and a poor identity test. A certificate that carries a glycine titration result and calls the material serine has not measured serine.

Specific rotation belongs to the serine side only. Glycine is achiral and has no rotation to report. The catalog range +14.0° to +16.0° is part of the L-serine specification, and it is not a shared amino-acid parameter that can be copied across to glycine.

IR, HPLC and the mass that separates them

Infrared spectroscopy distinguishes the two in the fingerprint region, because the hydroxyl group and the extra carbon change the spectrum. HPLC retention separates them if the method is designed for it. A single peak at one retention time is not proof unless the method was shown to resolve the other amino acid, and a method that runs one standard has not shown that.

LC-MS confirms the mass. Protonated serine appears at m/z 106.1 and protonated glycine at m/z 76.1, a 30-unit gap that matches the formula difference. Serine has one stereocentre, so L-serine and D-serine are enantiomers; glycine has none. A chiral HPLC method or the specific rotation is needed for serine and is not applicable to glycine.

X-ray diffraction can compare the crystal patterns, and the two are different solids. It is not a routine release test, and it does not measure the enantiomer. It is useful when the question is whether a lot is crystalline serine or an amorphous blend, not when the question is which amino acid is in the drum.

Two names, two ingredients

In the European Union, the ingredient list names each amino acid, and a blend that contains both must declare both amounts. A US Supplement Facts panel declares each dietary ingredient and its amount per serving. Format follows the market and the product; the brand's reviewer confirms it.

The L is part of the name for serine, because the enantiomer is part of the identity. Glycine has no L or D form, so “glycine” is complete. A specification that says only “serine” leaves the enantiomer open, and a label that says “serine” is ambiguous where the market requires the L form.

The two are not interchangeable in a formula. Glycine is not a “free-form” version of serine, and serine is not glycine with a filler. Each has its own specification, assay, identity test and label. A supplier who offers “amino acids” as a category has not specified either ingredient.

When to choose which

Use L-serine when the label and the formula are both about serine; use glycine when they are both about glycine. A blend that uses both needs both on the specification, both tested and both declared. This is a labelling and specification choice, not a ranking by purity.

The wider context is on the L-serine product page, the glycine product page and the L-threonine page. The assay lines are explained on the L-serine COA page; method notes sit under methods; the quality page describes release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation