L-ornithine free base or hydrochloride: choosing a grade
L-ornithine is sold as a free base or as a monohydrochloride, and the salt is not a diluted base. The base is 132.16 g/mol and is all ornithine; the hydrochloride is 168.62 g/mol, about 78.4% ornithine and about 21% chloride, and its solution is much less alkaline. The catalog material is the base at 40 mesh. Form and mesh are separate lines in the specification.
The hydrochloride carries about 78% ornithine and a chloride load, so the form changes the dose arithmetic and the label before it changes the assay.
Two decisions under one name
“L-ornithine” does not say which chemical form is in the drum. The base and the hydrochloride have their own CAS numbers, molecular weights, pH ranges and label names. A certificate written for one cannot be applied to the other, and a formula weighed for one will be over- or under-dosed if the other arrives.
The second decision is physical. The catalog grade passes 40 mesh at ≥95%; a granulated grade is available on request. Mesh changes flow, dust and the way the powder disperses, but it does not change the molecule. Write the chemical form and the particle size as two separate requirements.
Free base and hydrochloride
| Line | Free base | Hydrochloride |
|---|---|---|
| Label name | L-ornithine | L-ornithine hydrochloride |
| CAS number | 70-26-8 | 3184-13-2 |
| Formula and molecular weight | C5H12N2O2 · 132.16 | C5H13ClN2O2 · 168.62 |
| Ornithine per gram | 1.00 g | About 0.784 g |
| pH (1% solution) | 9.0–11.0 | Below the base; the salt's certificate states its range |
| Chloride | None from the counter-ion | About 21% by mass |
| Assay convention | 98.5–101.5% by HPLC; basis and entity stated | The salt's specification, calculated as the salt |
| Panel wording | L-ornithine | L-ornithine hydrochloride |
Neither row is a quality ranking. The form that fits the formula and the label is the correct one, and the other is a different purchase.
Alkalinity, water and the chloride load
The base is alkaline because it has two amino groups and no acid counter-ion. A 1% solution sits between pH 9.0 and 11.0. In a sealed stick with an acid, the base neutralises the acid; any carbonate the powder has picked up from the air can release carbon dioxide and swell the pack.
Water is the other handling issue. The base is hygroscopic, and its alkaline surface can also take carbon dioxide from the air. The powder cakes, the pH falls and the mass gains something that is not ornithine. The hydrochloride removes most of that alkaline surface, but it is still hygroscopic and brings about 21% chloride; it is a different formulation decision, not a free pass on the pouch.
Both forms dissolve readily in water, so solubility rarely decides the choice. The deciding factors are the pH the matrix can carry, the chloride the label can declare and the ingredient name the artwork already uses.
The dose arithmetic
Each gram of the hydrochloride supplies about 784 mg of ornithine. To declare 1,000 mg of ornithine from the salt, the formula needs about 1,276 mg of powder. A 500 mg capsule of the salt carries about 392 mg of ornithine, while the same fill of base carries about 500 mg.
That gap changes the fill weight and the panel. A capsule designed around 500 mg of base cannot hit the same label figure with the salt unless the fill or the capsule count changes. A stick pack offers more volume, though the acid–base reaction weighs more heavily in a sealed pack; a tablet adds granulation pH to the question; a gummy adds water and heat.
Decide the form before the purchase order. State the ornithine figure the label will declare and the fill weight the machine can run, then choose the salt or the base that meets both.
What the specification should say
- “L-ornithine free base only; CAS 70-26-8; C5H12N2O2. The hydrochloride is a separate purchase.”
- “Assay by HPLC: 98.5–101.5%, with the basis and entity stated.”
- “Specific rotation +22.0° to +24.0° on the dried basis, with solvent and concentration stated.”
- “Loss on drying ≤0.5%; pH (1% solution) 9.0–11.0.”
- “Particle size: at least 95% through 40 mesh, or the granulation agreed in writing.”
- “Chloride: report the result on every lot where the formula is sensitive to salt.”
- “Metal panel and micro counts as listed; lot code on the pack, certificate and retention sample.”
For the hydrochloride, the name, CAS, molecular weight, assay convention, pH range and chloride line all change. A base specification with the noun swapped is not a salt specification.
When the other form is the wrong choice
Do not put the base into an acidic, sealed powder unless the formula can handle the gas it will release. Do not put the hydrochloride behind a label that says “L-ornithine” and declares an ornithine dose, unless the panel is rewritten for the salt. Nor should the form be changed to solve a flow problem; mesh and granulation address flow, while a salt swap creates a labelling problem.
The catalog form is the free base at 40 mesh. The catalog sheet sits on the product hub; the COA page shows the reporting format; the ornithine versus arginine page covers the structural difference; the stability page covers moisture and gas; the compliance page covers the market names.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation