02 Grade comparison

Free L-leucine or a BCAA blend: choosing a grade

Technical document 02 · Reviewed 2026-11-19 · L-Leucine

On this page
  1. Two decisions hide behind the word “grade”
  2. Free L-leucine and a blend side by side
  3. What 40 mesh, 80 mesh and granulation change
  4. Fitting the form to the dosage form
  5. Writing the grade into the specification
  6. When not to switch

Free L-leucine and a BCAA blend sit in the same catalogue section, but they are different label declarations. The free form is a single amino acid at 98.5–101.5% on the dried basis; a 2:1:1 blend is a mixture in which leucine is only half the mass. The decision follows the label, the grams of leucine the formula needs and the dosage form, not the weight on the pack.

In one line

A BCAA blend is a formula, not a grade: the label, the leucine content per gram and the test panel all change when the form changes.

Two decisions hide behind the word “grade”

Grade is an overloaded word in this category. It can mean the chemical form — free L-leucine or a three-amino-acid blend — the physical form (40 mesh, 80 mesh, granulated), or a purity claim attached to either. A quotation that says only “leucine 99%” has not told you which of those it is selling.

For this product the molecule is L-leucine, CAS 61-90-5. DL-leucine is a different material with its own CAS 328-39-2, certificate and label; a BCAA blend is a mixture of three ingredients, not a variant of the free acid.

A titration does not settle the chemical-form question. A blend can be built to consume titrant inside the 98.5–101.5% window because the method counts amino groups, not leucine molecules. The label and the component assays are what separate the products.

Free L-leucine and a blend side by side

Free L-leucine, 2:1:1 and 4:1:1 blends by mass (rounded)
AttributeFree L-leucineBCAA 2:1:1BCAA 4:1:1
CompositionOne substanceThree amino acidsThree amino acids
Leucine per gram1.00 g0.50 g0.67 g
Isoleucine per gramNone0.25 g0.17 g
Valine per gramNone0.25 g0.17 g
Assay98.5–101.5% by titration, dried basisEach component by HPLC; ratio by massEach component by HPLC; ratio by mass
Label nameL-leucineL-leucine, L-isoleucine, L-valineL-leucine, L-isoleucine, L-valine
Identity checkIR and specific rotationComponent profile and ratioComponent profile and ratio
CertificateOne assay and one rotationThree assays plus blend uniformityThree assays plus blend uniformity

The arithmetic is simple and worth doing before the quotation is compared. In a 2:1:1 blend, leucine is 2 parts of 4, or 50% by mass; in a 4:1:1 blend it is 4 parts of 6, or 66.7%. An instantised or carrier-containing blend adds mass that is not amino acid, so the leucine figure is lower and the label should show it. Read the grams of leucine, not the grams of blend.

What 40 mesh, 80 mesh and granulation change

The reference cut is 40 mesh: at least 95% of the powder passes a 425 µm opening. Capsule fillers and ribbon blenders are usually set up around that cut, and it is the grade to quote unless the line has a reason to move. Milling to 80 mesh makes a finer powder that disperses faster in a small blend, but it also throws more dust, carries more static and is harder to keep from segregating away from a coarser excipient.

Granulation goes the other way: the particles are built up, so the powder flows more freely and fills a capsule or stick more evenly, while dissolving more slowly. Neither is an upgrade in the abstract. The filling line and the finished form decide, and a trial on the actual equipment decides between them.

A blend introduces a third physical risk. Three powders with different particle sizes and bulk densities can unmix in a drum, in a hopper or during stick filling. Ask for the particle-size distribution of each component and a homogeneity result on the blended lot; a mix that is uniform in the blender can still segregate on the way to the filler.

Fitting the form to the dosage form

A capsule or tablet line can run the 40 mesh powder as it arrives. A formula that carries a gram or more of leucine becomes a large tablet or a handful of capsules, so the granulated grade is often easier on the press; a compaction trial shows whether the press needs a binder or a bigger tool. Capsules tolerate a finer powder better, but a milled lot can arch over the hopper and slow the fill.

Sticks and drink mixes are harder, because the powder has to disperse into the serving volume. L-leucine is sparingly soluble, about 22 g/L at ambient temperature, so 3 g in 200 mL sits below saturation and 5 g in 200 mL sits above it and may leave a fine solid. More water, a coarser granule or a smaller serving each solves part of that; the trial belongs at the serving volume and temperature, not in a warm laboratory beaker.

Writing the grade into the specification

The specification is where the grade becomes enforceable. For free L-leucine it should name the substance and CAS 61-90-5, give the assay by titration on the dried basis, write the rotation with the solvent, concentration and temperature used, cap loss on drying at 0.5%, set residue at ≤0.1%, fix pH 5.5–6.5 at 5%, and specify the mesh — the 40 mesh cut (95% passing), or the milled or granulated variant ordered.

For a blend the specification needs more lines, not fewer: the ratio by mass, the assay of each of the three components, the blending and uniformity procedure, the particle-size distribution of each component, and the label declaration. “BCAA 2:1:1” on its own is a formula name, not a specification.

How a lot is released is set out on the COA page; how the L form is separated from a blend is on the identity page.

When not to switch

Do not switch free L-leucine to a blend to keep a label that says L-leucine. The label has to name every ingredient in the drum, and a blend that is declared as leucine is a labelling error before it is a specification error.

Do not switch a blend to free leucine if the artwork describes a 2:1:1 product: the ratio is part of the formula, and removing two components changes the serving size and the label.

Do not accept “leucine 2:1:1” without a component assay and a uniformity result, and do not compare a free-leucine quotation with a blend quotation on the invoice weight alone. The head-to-head comparison is on the L-leucine versus BCAA page; the label rules that follow the name are on the compliance page, and the catalog specification is on the product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation