01 COA & batch testing

What the L-arginine HCl certificate reports, line by line

Technical document 01 · Reviewed 2026-11-20 · L-Arginine HCl

On this page
  1. Reading the certificate line by line
  2. The percentage is a salt percentage
  3. The gate and the measured result
  4. What shifts between lots
  5. When an outside test earns its place
  6. Six lines to compare between suppliers

The certificate for an L-arginine hydrochloride lot reports appearance, identification by IR and titration, assay by titration, specific rotation, loss on drying, the heavy-metal panel, microbiology and particle size. The assay is calculated as the hydrochloride, so a 99.0–101.0% figure is a salt figure: about 82.7% of that mass is arginine. The limits in the tables below are the catalog gates; the batch COA is the document that confirms a particular pouch or drum.

In one line

The assay counts the whole hydrochloride, so a 99.0–101.0% titration result is about 83% arginine and the salt figure must not be read as a dose.

Reading the certificate line by line

A certificate can be audited when every line answers three questions: what was measured, which method produced the number, and which limit the lot was released against. A row that says only “conforms” records a conclusion and hides the evidence. For this material the identification row and the rotation row decide that the powder is the L form of the hydrochloride, and the assay row decides how much of it is present.

Identity, assay and moisture · L-arginine hydrochloride
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
IdentificationIR and titrationConforms to the reference
Assay, calculated as C6H14N4O2·HClTitration99.0–101.0%
Specific rotationPolarimetry, c=2 in 5 M HCl+21.0° to +23.0°
Loss on dryingGravimetric≤0.5%

IR and titration answer different questions. The IR spectrum compares the functional groups with a reference; the titration measures the basic centres of the molecule. Neither test alone shows the L configuration or the water content, which is why the rotation and the loss on drying sit beside them.

The percentage is a salt percentage

The molecular weight of the hydrochloride is 210.66 g/mol, of which 174.20 g is the arginine entity. One gram of salt therefore contains about 827 mg of arginine, and a 100.0% assay means 82.7 g of arginine per 100 g of powder. The catalog window of 99.0–101.0% corresponds to about 81.9–83.5% arginine, before the moisture correction.

Loss on drying is the second correction. At 0.5% water, the as-is salt content is 99.5% of the dried-basis figure, and the as-is arginine content falls by the same 0.5%. The certificate should say whether the assay is reported on the dried basis or as-is; the catalog pairs the titration range with a ≤0.5% loss on drying, and that pair is what lets a formulator move between the two.

The free base has its own assay, 98.5–101.5% on the dried basis, calculated as the base. The two numbers look similar and mean different things: 99.5% of the hydrochloride is about 82.3% arginine, while 99.5% of the base is about 99.5% arginine. Comparing the two assay figures without the molecular weight is the commonest arithmetic error in a form change.

The gate and the measured result

The release limit defines what the lot had to meet; the batch result records what the laboratory found. Each number needs its own column, with the method named next to it. Copying the range into the result column tells the reader nothing about the lot.

What the result column should contain
ParameterRelease limitResult column
Assay99.0–101.0% as the saltA measured percentage, with the basis and the titrant
Specific rotation+21.0° to +23.0°A measured angle, with concentration, solvent and temperature
Loss on drying≤0.5%A measured percentage
Heavy metalsPer elementA measured figure in mg/kg for each element
Particle size≥95% through 80 meshA measured percentage through the sieve

Some rows deserve a second look even when they pass. A rotation just above +21.0° leaves little room for temperature or concentration error. A loss on drying near 0.5% leaves little room for a humid filling room. A particle-size result close to the 80 mesh gate matters most for a capsule line that depends on flow.

What shifts between lots

Moisture is the first mover, because the salt is hygroscopic: a pouch opened in a humid room gains water quickly, and the loss on drying rises while the dried-basis assay stays flat. Colour is the second: white to off-white is a wide window, and a tan or cream tint can follow the drying step or a longer hold. Milling sets the 80 mesh result, so a change of mill or sieve can move the particle-size figure without any change in the chemistry.

A genuine L-form lot keeps its rotation inside the window from batch to batch. Because the catalog value is defined at c=2 in 5 M HCl, a certificate that omits the solvent and the concentration cannot be compared with another certificate; the number is only meaningful with its conditions. A drift across lots is more informative than one result at an edge, because it points to a change of source or purification.

When an outside test earns its place

An outside test is worth ordering when the source is new, when the lot is the first into a regulated market, when the form is contested, or when a result sits on a limit. An outside panel should add what the routine certificate leaves out: chloride by ion chromatography or argentometric titration, polarimetry with its conditions, an amino-acid HPLC profile, IR against a reference, ICP-MS and a micro count, beside the titration and the loss on drying.

Because arginine has no usable ultraviolet chromophore, the HPLC identity normally needs derivatisation, ion-exchange with post-column ninhydrin, or mass detection. The report should name the technique and the detection limit; a “not detected” line without a limit describes the method, not the sample. The referee should receive the retained sample, the supplier's certificate and the specification, all under one lot code.

Six lines to compare between suppliers

Put six lines side by side: the form and CAS number; the assay with its basis, calculated as the salt; the specific rotation with solvent and concentration; the chloride result; the loss on drying; and the mesh with the pack size. When two offers match on assay but part company on the other five lines, they are not offers for the same powder.

Then check traceability: the lot code on the certificate, the pouch or drum, and the retained sample should be the same, and the certificate should name the producer rather than only the trader. The catalog specification is on the L-arginine HCl product page; the free-base comparison is on the L-arginine page; the release workflow is on the quality page; the chromatographic and spectroscopic methods are collected in the methods library; the form arithmetic is worked through on the grades page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation