02 Grade comparison

Pure ergothioneine or a dilution: choosing a grade

Technical document 02 · Reviewed 2026-11-19 · Ergothioneine

On this page
  1. Why a 99.5% material still has grades
  2. The three forms side by side
  3. What particle size changes
  4. Matching the grade to the dosage form
  5. What to write into the specification
  6. When a dilution is the wrong choice

For a single chemical entity the grade question is not a potency ladder: the catalog material is already ≥99.5% by HPLC. What changes between grades is the physical form — a 40 mesh crystal, an 80 mesh milled powder, or a dilution on a carrier — and that choice changes the fill weight, the content uniformity and the label, not the identity. The grade has to be chosen from the dose and the dosage form, then written into the purchase specification.

In one line

The pure substance is fixed at ≥99.5%; the grade decision is about particle size, carrier and dose per gram, and the label has to follow it.

Why a 99.5% material still has grades

Most ingredients are sold as a range of potencies, so buyers learn to read the percentage first. L-ergothioneine does not work that way. On the pure material, the catalog specification fixes the assay at ≥99.5% and the rotation at ≥ +122°, and neither moves between the 40 mesh and the 80 mesh forms. What moves is how the powder behaves in a blender, a capsule filler and a stick-pack machine.

The commercial unit is the milligram, not the kilogram. A capsule may carry 5 to 30 mg of ergothioneine; a stick pack or a gummy may carry a similar dose inside several grams of matrix. At that scale the pure crystal is a small part of the fill, and the rest of the fill has to be chosen deliberately rather than left to the excipient list.

A dilution is not a weaker version of the same grade; it is a different material. It has a carrier, a different assay, its own homogeneity requirement and its own label declaration. Reading it as the same material at a lower assay is how a formulation ends up under-dosed.

The three forms side by side

Catalog forms · L-ergothioneine
FormWhat it isErgothioneine per gramFits
Crystalline, 40 mesh≥99.5% pure, unmilled crystalAbout 995 mgCapsules, tablets, dry blends
Milled, 80 meshSame assay, finer particleAbout 995 mgLow-dose blends, suspensions
DilutionPure material on an agreed carrier, stated percentageSet by the ratio, e.g. 100 mg at 10%Sticks, gummies, very low doses

The first two rows differ only in particle size, and both carry no carrier. The third is a formulated material and needs a specification of its own. The pure versus dilution page works through the arithmetic and the uniformity question in detail.

What particle size changes

Mesh is a sieve number, not a quality rank. A 40 mesh powder passes a sieve with openings of about 420 µm; an 80 mesh powder passes about 180 µm. Both are the same crystal at the same assay, but they do not behave the same way in a plant.

The coarser 40 mesh powder flows more freely, generates less dust and is easier to weigh in a dry room. The finer 80 mesh powder disperses more evenly through a low-dose blend and stays suspended more readily, but it flows less freely and generates static and airborne dust. For a capsule filled by weight at a dose well below the fill weight, uniformity usually matters more than flow; for a high-speed tableting line, flow usually wins.

A dilution adds a second variable: the carrier. If the carrier's particle size and bulk density do not match the pure material, the blend can segregate in the drum, in the hopper or in the capsule bowl. Matching the carrier to the powder is a formulation decision, and it should be made before the dilution is ordered rather than after the first homogeneity failure.

Matching the grade to the dosage form

Capsules. At 20 mg in a 400 mg fill, the pure powder is 5% of the capsule. That is a small number to weigh accurately and to distribute through the fill, and a pre-made dilution at a matched ratio is often the more robust route. The alternative is to keep the pure material and accept that most of the fill is excipient.

Tablets. Direct compression wants flow and compressibility. A fine, low-dose active is a content-uniformity risk, so a dilution on a compressible carrier can be the better choice; a high-dose tablet is easier with the pure crystal and a well-designed granulation.

Stick packs and sachets. The fill is measured in grams, and the active is a fraction of a percent of it. A dilution is the practical way to weigh and blend at that ratio, provided the carrier is soluble and does not add a taste or a moisture problem.

Gummies and chews. The matrix is wet and warm, so the powder is added into a process rather than a dry blend. Dispersion and water activity matter more than mesh; the stability questions are covered on the stability page.

What to write into the specification

For the pure material, the grade line is short: “L-ergothioneine, ≥99.5% by HPLC, 40 mesh, no carrier.” Add the rotation and the moisture limit from the catalog, and the line describes a material that can be tested on receipt.

For a dilution, the line has to carry more: the percentage of L-ergothioneine, the identity of the carrier, the assay range for the blend, the homogeneity requirement and the method used to test it. “L-ergothioneine 10% on maltodextrin, blend assay 9.5–10.5% by HPLC, homogeneity RSD ≤5% across ten sample points” is a specification; “ergothioneine blend” is not.

The blend also needs its own certificate. The pure material's COA stops at the drum that was diluted; the blender becomes the manufacturer of the blend and should issue the release document for it. A buyer who accepts the pure COA as cover for a dilution has no result for the material actually received.

When a dilution is the wrong choice

A dilution stops making sense when the dose is large enough that the extra carrier becomes the dominant mass. A 100 mg dose from a 10% blend needs a gram of powder per unit; from the pure material it needs 100 mg. The fill weight, the capsule size and the shipping volume all follow the arithmetic.

It is also the wrong choice when the carrier brings a problem: a reducing sugar or a high-moisture carrier in a hygroscopic powder, a carrier that cannot be declared on the label, or a customer specification written for the pure substance. And it is the wrong choice when the ratio is not justified by the dose — a 1% dilution ordered for a 5 mg dose means 500 mg of blend per unit, which is a formulation decision that should be made on purpose.

The specification for the chosen grade sits on the L-ergothioneine product page; the certificate rows are explained on the COA page; the packs and minimum order are on the ordering page; and sieve sizes are defined in the particle-size note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation