80 mesh, 200 mesh or micronized: choosing a creatine grade
The grade is a particle-size decision, not a purity decision. An 80 mesh cut is the general-purpose powder for dry blends and capsules; a 200 mesh cut is finer, for stick packs and faster dispersion; a micronized grade is a distribution agreed by laser diffraction, used where mouthfeel and suspension matter. All three are creatine monohydrate and carry the same assay, creatinine, dicyandiamide and loss-on-drying limits.
Mesh changes the powder's behaviour in the line, not the molecule in the drum.
Why the grade is a processing question
Creatine monohydrate has one identity: the hydrate of creatine, CAS 6020-87-7. Milling does not change the assay, the impurity limits or the water of crystallisation. What changes is how the powder moves, how much air it carries, how fast it wets and how much mass fits into a capsule, a scoop or a stick.
“80 mesh” and “200 mesh” are sieve cuts and can be written as a pass-through requirement. “Micronized” has no single definition in the trade: one supplier may mean a 200 mesh cut, another a jet-milled powder with a median well below it. A micronized grade should be specified as a distribution, such as a D50 and a D90 by laser diffraction, with the method named.
Three cuts, three behaviours
| Grade | Particle size | Flow and dust | Dispersion | Typical fit |
|---|---|---|---|---|
| 80 mesh | Passes an 80 mesh sieve, about 177 µm | Free-flowing; low dust | Wets with stirring; can feel gritty in a fine suspension | Capsules, tablets, dry blends, drum handling |
| 200 mesh | Passes a 200 mesh sieve, about 74 µm | Slower flow; more dust and static | Faster wetting; smoother mouthfeel | Stick packs, drink mixes, tight capsule fills |
| Micronized | Distribution agreed by laser diffraction; finer than 200 mesh | Cohesive; bridges and dusts | Fastest dispersion; least grit | Fine-dispersion mixes, suspensions, small fills |
The sieve figures are nominal: 80 mesh is about 177 µm and 200 mesh about 74 µm. A certificate that names only the mesh leaves the method and the fines content open, so ask for the sieve standard and the percentage passing.
Flow, bulk density and loss on drying
Flow is the first thing the line notices. A coarser cut has less surface area per gram, absorbs less moisture from the air and pours more predictably. A finer cut has more particle-to-particle contact, holds more air and tends to bridge in a hopper, cling to a chute or puff out of an open port. Micronized powder is the most cohesive of the three and usually needs either a forced feeder or a granulation step before it will run at speed.
Bulk density follows the same pattern. The finer the powder, the more air is trapped between particles and the lower the bulk density, so a fixed fill volume holds less mass. That is why a grade change can move a capsule fill weight or a stick-pack fill target without any change in the chemical specification. Measure bulk and tapped density on the actual grade, and test the flow in the actual hopper rather than on a bench.
Loss on drying is not a grade property. Every grade is the monohydrate and is released against the same ≤12.0% limit, because the water of crystallisation is part of the material. A finer cut does not justify a lower LOD, and a low LOD is not evidence of a better grade; it may mean the powder has been over-dried or that a different hydrate was supplied. Keep the LOD limit and the particle-size method as separate lines.
What changes in the capsule, stick or tablet
In a capsule, fill weight is set by volume and powder density before it is set by the label. A finer grade at the same fill volume delivers less mass, and a poorly flowing grade gives weight variation across the run. An 80 mesh cut is usually the easier starting point; a 200 mesh cut may be needed when the capsule is small or the blend must be uniform, with the feeder adjusted for the lower density.
In a tablet, the grade affects segregation, flow and content uniformity. A coarser cut blends and flows well but can segregate from fine excipients; a finer cut distributes more evenly but may bridge in the feed frame. A grade change should be tried on the press, not only in a sieve analysis.
In a stick pack or a drink mix, the 200 mesh cut is the usual choice: it wets faster, feels less gritty and stays suspended longer than the coarse cut. The trade-off is dust at the filling head and powder on the seal, which is a machine and hygiene issue as much as a product issue. A micronized grade goes further in the same direction, but it can float on water or form lumps if it is dumped in too quickly; a short high-shear step or a pre-blend with a carrier usually fixes that.
None of this alters the amount of creatine in a gram of powder: the label declares the monohydrate mass, and the grade only changes how that mass behaves. If the product needs a clear solution, no mesh will deliver it; creatine monohydrate has limited solubility, roughly 13 g/L at room temperature, and a finer powder dissolves faster only up to that limit.
The specification for a grade switch
A grade specification needs four things beyond the chemical lines: the grade name, the particle-size method, the acceptance range and the bulk-density or flow target if the line depends on it. For a sieve cut, write the mesh and the percentage passing. For a micronized grade, write D50 and D90 by laser diffraction and name the dispersion method, because the same powder can report different distributions under different preparation.
- “Creatine monohydrate, 80 mesh; ≥95% through an 80 mesh sieve; sieve standard named.”
- “Creatine monohydrate, 200 mesh; ≥95% through a 200 mesh sieve; sieve standard named.”
- “Micronized: D50 and D90 by laser diffraction, method and dispersant named.”
- “Assay, creatinine, dicyandiamide, LOD, ROI, heavy metals and microbiology unchanged from the catalog specification.”
Then re-qualify the line, not only the drum: fill weight, weight variation, dispersion time, content uniformity and dust. A grade change that passes the COA can still fail the fill target without any chemical line changing.
When the current grade is already right
If the current grade runs well and the finished product meets its fill and dispersion targets, a finer grade adds milling cost and slows the line without improving the product. A finer cut helps a gritty drink, not a slow dissolve at the solubility limit. If the problem is creatinine, moisture or caking, the answer is in the dryer, the pack and the storage, not the sieve.
The product page carries the catalog specification; the COA page shows how mesh and LOD sit on the certificate; the monohydrate versus micronized page takes the flow and fill question further; the stability page covers moisture and heat; the particle-size glossary entry defines the sieve and laser methods.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation