06 Identity & adulteration

How we prove a wheat protein peptide lot is what it says

Technical document 06 · Reviewed 2026-11-19 · Wheat Protein Peptides

On this page
  1. The four identity layers
  2. The ratios worth calculating
  3. What X-ray diffraction can and cannot show
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Five questions for the supplier

A wheat peptide is not proved by its protein percentage. The file needs the wheat source, a peptide distribution that is consistent with hydrolysis, an amino acid profile that looks like wheat and not like collagen or soy, and an allergen statement that matches the source. A highly hydrolysed powder is a poor DNA sample, so the documentary and compositional layers carry more weight than a single PCR result.

In one line

A wheat peptide is identified by the source record, the nitrogen and peptide figures, the amino acid fingerprint and the allergen statement; the protein percentage alone does not name the material.

The four identity layers

Four layers answer four different questions. The source record is documentary. The protein and peptide figures say the powder is a hydrolysate. The amino acid profile says the protein looks like wheat. The allergen statement ties the powder to the source. None of them is sufficient alone.

Four layers of wheat protein peptide identity
LayerQuestionEvidenceWhat it proves
SourceIs the raw material wheat?Wheat declaration, raw-material records, supplier auditThe source, not the powder
CompositionIs it a protein hydrolysate?Protein by Kjeldahl, peptide content by HPLCProtein and peptide content
SizeHow far was it hydrolysed?HPLC peptide distributionProcess consistency
FingerprintDoes it look like wheat?Amino acid profileConsistency, not source proof

Wheat gluten has a distinctive amino acid shape: glutamic acid and glutamine dominate, proline is high, lysine is low, and hydroxyproline is absent. Soy and pea are higher in lysine; collagen and gelatin bring hydroxyproline. The profile does not prove wheat, but it makes several substitutions visible.

The ratios worth calculating

Start with peptide divided by protein. At the catalogue floors, 70.0 ÷ 80.0 = 0.875, so about 87.5% of the protein is counted as peptide. A result above 1.0 means the two methods are not on the same basis. A much lower figure points to intact protein, free amino acids or a different integration cut-off.

Check nitrogen against protein next. At N × 5.70, an 80.0% protein figure requires about 14.0% nitrogen; at N × 6.25 it requires 12.8%. If the nitrogen result multiplied by the stated factor does not equal the protein figure, either the factor or the basis is wrong.

Check ash against protein. Ash up to 5.0% with protein at 80.0% is possible, but ash near the limit with a clean protein figure suggests salt from neutralisation or a mineral carrier. Sodium and chloride are the follow-up tests. None of these ratios is a release limit unless the specification says so.

What X-ray diffraction can and cannot show

A spray-dried peptide is amorphous, so its diffractogram is a broad halo rather than a sharp pattern. XRD will not identify wheat peptides or separate them from soy or pea peptides. A “conforms” statement without a reference pattern and a detection limit is an empty comparison.

XRD has a narrow use: it finds crystalline material in an amorphous powder, such as sodium chloride, a crystalline amino acid or a mineral carrier, and it can show a solid-state change after storage or granulation. Use it for that question, not as a routine release identity test for this product.

What adulteration looks like

The economic substitutions are a carrier, a substitute protein, collagen, free amino acids, salt or a non-protein nitrogen source. Colour and taste are weak evidence because the powder naturally varies; the mass balance, the amino acid profile and the source record are stronger.

Common wheat protein peptide substitutions and the signals
AdulterantWhat it doesSignalTest
Maltodextrin or carrierLowers protein and peptide per gramProtein and peptide low; ash normalMass balance, HPLC, label
Soy or pea proteinSubstitute plant nitrogenLysine rises; profile shiftsAmino acid analysis, peptide profile
Collagen or gelatinRaises protein and hydroxyprolineHydroxyproline presentHydroxyproline, amino acid profile
Free amino acids or MSGSmall-molecule nitrogen and tasteFree amino acids high; sodium risesAmino acid analysis, HPLC, sodium
Salt or mineral carrierRaises ashAsh high; sodium or chlorideAsh, ICP-OES, chloride
Non-protein nitrogenRaises Kjeldahl without peptideProtein high, peptide lowNitrogen/protein ratio, amino acid profile

Hydroxyproline is the collagen flag, not a wheat marker. Sodium is the salt flag, and it can explain ash and taste without any protein substitution.

Writing identity into the specification

A specification that can be checked names the evidence, not just the product:

  • “Wheat protein peptides; wheat raw material and hydrolysis process named.”
  • “Protein ≥80.0% by Kjeldahl; factor and basis printed.”
  • “Peptide content ≥70.0% by HPLC; method and cut-off named.”
  • “Peptide distribution reported; amino acid profile reported.”
  • “No carrier unless declared; no collagen or gelatin present.”
  • “Moisture ≤7.0%; ash ≤5.0%; heavy metals and microbiology as listed.”
  • “Wheat allergen statement on file; gluten result where claimed.”

Five questions for the supplier

  1. Which wheat raw material and hydrolysis process produced this lot, and which document supports it?
  2. What nitrogen factor and basis were used for the protein figure?
  3. How is peptide content measured, and what cut-off defines a peptide?
  4. Can you provide the peptide distribution and the full amino acid profile?
  5. If identity is disputed, will you agree to a joint re-test on the retained sample?

Those five answers make an identity file; a single assay figure does not. The product hub carries the catalogue specification; the COA page shows where each figure sits; the grades page compares the practical options; the wheat peptides versus gluten page covers the allergen question; the analytical methods library explains the HPLC work; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation