10% or 20% undenatured type II collagen: choosing a grade
Two grades are offered: a 10% powder and a 20% powder, both standardized by ELISA inside the same 10.0–20.0% catalogue range. The grade decides how much powder carries a given amount of native type II collagen, and therefore the capsule size, the stick weight and the label arithmetic. It does not change the source, the assay or the protein floor.
The grade is the ELISA target, not the protein percentage: 10% and 20% are two standardization points inside one catalogue range, and the choice follows the fill weight the label has to hit.
Standardization is the product
Chicken sternum does not arrive at a constant native collagen content. The tissue varies with the bird, the cut and the season, and the extraction decides how much of the triple helix survives. Standardization turns that variable extract into a powder with a declared native content, and the declared value is the grade. A 10% grade targets 10 g of native type II collagen per 100 g of powder; a 20% grade targets 20 g. Both sit inside the catalogue range, and the release window for each grade is agreed in the specification.
The protein figure does not track the grade. Both grades carry a protein floor of 50.0% by Kjeldahl N × 6.25, because the powder is mostly protein either way. A 20% grade is not twice as protein-rich as a 10% grade; it carries twice the native type II collagen per gram at the target, with less of the other sternum material alongside it. That distinction matters when a quotation compares the two on the protein line and calls the higher figure the better grade.
Standardization also explains the 10.0–20.0% range on the certificate. The range is the window the catalogue supports, not a licence to ship any point inside it against a fixed label. The grade fixes the target; the certificate reports the lot against that target.
10% and 20% side by side
| Point | 10% grade | 20% grade |
|---|---|---|
| Native type II target | 10% by ELISA | 20% by ELISA |
| Powder per 100 mg native | 1,000 mg | 500 mg |
| Protein floor | ≥50.0% (N × 6.25) | ≥50.0% (N × 6.25) |
| Moisture and ash | ≤8.0% / ≤10.0% | ≤8.0% / ≤10.0% |
| Particle size | ≥95% through 80 mesh | ≥95% through 80 mesh |
| Catalogue status | Standard grade | On request |
| Fill consequence | Larger powder weight per serving | Smaller powder weight per serving |
The two grades share the specification lines that describe the powder, and differ on the line that describes the native content. That is the whole comparison. A quotation that lists only "type II collagen 10–20%" has not told the buyer which grade is being offered, and a purchase order that does not name the target leaves the release window open.
What stays the same, and what does not
Both are off-white to light tan powders, both are milled to 80 mesh, and both disperse in water rather than dissolving. The native collagen does not give a clear solution at either grade. What can differ is the standardization blend behind the target: a 20% grade needs a more concentrated component, and the blend can change bulk density, flow and the way the powder fills a capsule or a stick. Those are measured properties, not assumptions, and they belong in the trial rather than in the specification alone.
The ash limit is the same 10.0% on both grades, but the actual ash can differ if the more concentrated component carries a different mineral load. The same applies to colour and odour. A grade change is a supplier and process change even when the catalogue lines look identical, so ask for the certificate of the grade you are buying, not the certificate of the grade family.
The arithmetic of the fill
The serving arithmetic is simple and it drives the format. If the label declares 100 mg of native type II collagen per serving, the 10% grade needs 1,000 mg of powder and the 20% grade needs 500 mg. At 50 mg, the figures are 500 mg and 250 mg. The powder weight, not the grade name, is what the capsule shell or the stick has to hold, and a capsule has a fixed volume.
Two rules follow. Set the fill from the minimum native content the lot is released at, not from the target, or the label claim can fall short at the low end of the release window. And decide the overage policy with the supplier before the label is fixed: an overage on the native content is a commercial and regulatory decision, not a production detail. The COA page explains how the release window is read.
What changes when you switch
Switching grade changes five things: the powder weight per serving, the capsule or stick size, the overage, the label figure and the stability load. It does not change the source, the ELISA method or the contaminant limits. If the fill weight stays the same and the grade moves from 10% to 20%, the native content per serving doubles; that is a label change, not a capsule change. If the fill weight is halved to keep the same label, the capsule can be smaller and the excipient load changes with it.
Write the grade into the specification as a target with a release window, and name the ELISA method beside it. State the powder weight per serving and the basis on which the label figure was calculated. Ask for change control on the standardization blend, because a new blend can meet the same target and still change the flow, the colour and the fill. For the grade decision in the context of the other form, see undenatured versus hydrolysed collagen.
The 10% grade is the standard grade and the 20% grade is made on request; the ordering sequence is on the MOQ page. The full range is on the product page, and the particle-size definition is in the particle-size glossary entry.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation