01 COA & batch testing

What the COA for marine collagen actually contains

Technical document 01 · Reviewed 2026-11-20 · Marine Collagen

On this page
  1. The certificate as a test report
  2. The factor, the basis and the two SEC figures
  3. Release limit versus lot result
  4. What moves between lots
  5. When to order an outside test
  6. What to compare between suppliers

The certificate for a marine collagen lot reports protein by Kjeldahl with the 5.55 factor, peptide content and molecular weight by SEC, loss on drying, ash, the heavy-metal panel, microbiology and particle size. The source line should name fish skin and, where the buyer needs it, the species. The limits below are catalog values; the batch certificate is the document that proves a specific pack.

In one line

The protein figure only becomes comparable when the certificate prints the Kjeldahl factor, the assay basis, the SEC peptide distribution and the fish source beside it.

The certificate as a test report

A marine collagen certificate is readable when each line carries a parameter, a method and a release limit, and when the measured result sits in its own column. The table is the catalog specification for this grade, not a lot result; the measured values belong on the certificate that travels with the drum and the retained sample.

Release parameters · marine collagen, catalog specification
ParameterMethodRelease limit
ProteinKjeldahl, N × 5.55≥90.0%
Peptide contentSEC-HPLC≥80.0%
Molecular weightSEC-HPLC≥80% below 3,000 Da
Loss on dryingGravimetric≤7.0%
AshGravimetric, furnace≤5.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Appearance belongs on the same sheet: off-white to pale yellow, free-flowing powder. Colour is not a quantitative test, but it moves with the raw material and the dryer.

The factor, the basis and the two SEC figures

Kjeldahl measures nitrogen, not protein. The titration becomes a protein figure only after multiplication, and collagen uses N × 5.55 because the protein carries close to 18% nitrogen. A general food protein uses 6.25, which assumes 16%. Because 6.25 is about 12.6% larger than 5.55, the same nitrogen result reads 90.0% with one factor and roughly 101% with the other. The powder did not become richer; the convention changed.

The basis is the second half of the same question. The catalog sets protein at ≥90.0%, and the certificate should print whether the result is on the as-is or the dry basis. At the 7.0% moisture limit, 90.0% on the dry basis corresponds to about 83.7% as-is. A formulator who weighs the powder needs the as-is figure.

Peptide content and molecular weight are both SEC-HPLC results, but they answer different questions. Peptide content is the share of the powder that elutes as peptide rather than as free amino acid or non-peptide material. The molecular-weight line says how much of that peptide sits below 3,000 Da. A lot can pass the first gate and still carry a high-molecular-weight tail, so the certificate should report the distribution bins, not only the cut-off.

The certificate should also report the source in words. CAS 9007-34-5 is the generic collagen number and does not name fish, let alone the species, so the written source line is the only place the claim can be checked. The identity page sets out how the collagen, peptide and species claims are supported.

Release limit versus lot result

The release limit is the gate; the lot result is the reading. They belong in separate columns, each next to its method, and a result column filled with the catalogue range is a copy of the gate rather than a measurement.

Reading the result column · release limit against lot result
ParameterRelease limitResult column
Protein≥90.0%A measured percentage with the factor and the basis
Peptide content≥80.0%A measured percentage by SEC-HPLC
Molecular weight≥80% below 3,000 DaThe measured fraction below 3,000 Da and the bins
Loss on drying≤7.0%A measured percentage
Ash≤5.0%A measured percentage
Particle size≥95% through 80 meshThe measured percentage through the sieve

A tick in a “conforms” column is the end of a chain of evidence, not the evidence itself. Microbiology needs a count and an absence statement; the metal panel needs a number for each element. A single total for the metals says nothing about which one is close to its limit.

What moves between lots

Fish skin is a seasonal raw material. The species mix, the chilling and the time before processing move the collagen and the lipid load; hydrolysis time, temperature and enzyme dose move the peptide distribution; the dryer and the mill move moisture, colour and mesh. Ash moves with the raw material and with the washing steps, and a lot at 4.5% ash is not the same powder in a clear drink as a lot at 1.5%, even when both sit inside the 5.0% limit.

Odour is hard to put on a certificate and often the most informative line. A marine note is expected in this material, and it can strengthen with moisture, heat or residual lipid. A lot can pass every number and still smell unlike the previous drum, so keep a retained sample and a sensory note.

Mesh is a finishing variable: a new mill or a new sieve can move the 80 mesh result without touching the chemistry, and the flow, the dust and the wetting change with it. A trend across lots matters more than one result near an edge.

When to order an outside test

An outside laboratory earns its place when the source is new, when the first commercial lot enters a regulated market, when a species claim is not proven by the certificate, or when a result is disputed. Do not repeat the whole certificate. The panel that closes the question is hydroxyproline and the amino acid profile for collagen, SEC for the peptide distribution, a species-specific PCR or a documented species chain for the fish claim, ICP-MS for the metals, and loss on drying and microbiology on the same sample.

Every screen should come with its detection limit. A “not detected” entry without one describes how far the method can see, not what the sample contains. For a species test, the sample should be the powder as shipped rather than the raw tissue, unless the raw material is the question.

Keep the chain intact: the material that was tested should be the material that was kept, and the lot code should appear on the report. If a result is challenged, the referee needs the kept sample, the specification and the supplier's certificate.

What to compare between suppliers

Six rows make a supplier comparison: source and species; protein with factor and basis; peptide content and distribution; moisture and ash; mesh and appearance; allergen statement and country of origin. Two quotations that agree on the protein percentage and disagree on the other five are not quoting the same powder.

The second layer is traceability: the plant, the raw batch, the hydrolysis and drying record, and the retained sample. The catalog specification sits on the marine collagen product page. The fish collagen peptides page shows the neighbouring grade with a tighter peptide gate; the methods library covers the analytical techniques; the quality page describes the release file and the retained sample.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation