01 COA & batch testing

What the COA for elastin peptides actually contains

Technical document 01 · Reviewed 2026-11-19 · Elastin Peptides

On this page
  1. The lines on the sheet
  2. Protein, peptide and the factor between them
  3. Release limit and lot result
  4. What moves between lots
  5. When to send a sample out
  6. Six lines to compare

An elastin peptide certificate carries three figures that are often read as one: protein by Kjeldahl, peptide content by HPLC and the desmosine crosslink that marks elastin. Around them sit ash, moisture, heavy metals, microbiology and particle size. The figures below are the gates the catalogue sets; the batch COA reports what a particular lot measured.

In one line

The protein figure, the peptide content and the desmosine marker answer three separate questions, and no one of them identifies an elastin peptide on its own.

The lines on the sheet

Each line has to carry its method. A protein percentage without the nitrogen factor, a peptide content without the chromatographic mode and a desmosine result without its hydrolysis and detection cannot be compared between suppliers. The table lists the gates; it does not report a lot.

COA parameter list · elastin peptides, catalogue specification
TestMethodAcceptance boundary
AppearanceVisualOff-white to light tan powder
ProteinKjeldahl, nitrogen factor stated≥90.0%
Peptide contentHPLC, mode stated≥80.0%
DesmosineHPLC or LC-MS/MS after hydrolysisReported; basis stated
AshGravimetric, furnace≤5.0%
MoistureGravimetric, 105 °C≤7.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

The protein line says how much nitrogenous material is present; the peptide line says how much of it is in peptide form. Neither proves elastin. The desmosine line does, and it is the one most often missing from a copied certificate.

Protein, peptide and the factor between them

Kjeldahl measures nitrogen, not protein, and the nitrogen is multiplied by a convention. The general food-protein factor is 6.25; collagen uses 5.55 because its nitrogen content is higher. The factor for an elastin peptide must be stated, because the same nitrogen result becomes a different protein percentage under each convention: 14.4% nitrogen reads 90.0% at N × 6.25 and 79.9% at N × 5.55.

The basis deserves the same attention as the factor. Take a lot at the 7.0% moisture limit: a 90.0% dry result is only about 83.7% once the water is counted back in, and that is the figure a formulation works with. Name both the factor and the basis in the same row.

Peptide content is a separate measurement. The catalogue requires ≥80.0% by HPLC, and the method should say whether the result is a size-exclusion fraction, a peak-area sum or a nitrogen-based calculation. A protein result of 90% and a peptide result of 80% are not in conflict: the gap can be free amino acids, ash, moisture and non-peptide nitrogen.

The desmosine line needs its own detail. Desmosine and isodesmosine are pyridinium crosslinks formed from lysine and survive the acid hydrolysis used to release amino acids. The laboratory separates them by HPLC at 275 nm or LC-MS/MS and reports against protein or amino acid residues. Fish elastin carries less desmosine than mammalian elastin, so a figure is meaningful within a declared source, not as a universal pass mark.

Release limit and lot result

The limit is the boundary; the result is the measurement. Each needs its own column and its method. A result that echoes the range says nothing about the lot.

Reading the result column against the limit
TestBoundaryWhat the result must show
Protein≥90.0% with factor and basisA measured percentage, the factor used and the basis
Peptide content≥80.0% by HPLCThe measured percentage and the HPLC mode
DesmosineReportedA result per gram of protein or per 1,000 residues, with the method
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 80 meshThe measured percentage through the sieve

“Conforms” is a conclusion, and the reader should be able to reach it from the numbers. Microbiology needs a count and an absence statement; metals need one figure per element rather than a combined total. Ash is the quiet line: at up to 5.0% it can carry weight that is not protein.

What moves between lots

The raw material moves first. Elastin is purified from an elastin-rich tissue, and its amount depends on the species, the tissue, the age of the animal and the season. Where a plant runs several tissues, the desmosine level and the amino acid pattern move with the blend, even if the hydrolysis programme stays the same.

Hydrolysis comes next. How far the chains are cut depends on time, temperature and enzyme dose, and that in turn sets the peptide content and the size distribution. Drying fixes the moisture, the colour and part of the flow behaviour; neutralisation and washing decide the ash.

Read the sequence, not one number: protein easing down over three lots, peptide content slipping, ash rising, or a desmosine figure that no longer fits the source is a stronger signal than a single result near a limit. Pouch, drum and retained sample should carry the same code.

When to send a sample out

An outside laboratory earns its fee when the source is new, when a regulated market is being entered for the first time, when the label says elastin but the certificate stops at protein, when a blend is suspected, or when two laboratories disagree. The useful panel is the amino acid composition, desmosine and isodesmosine, the peptide distribution, ICP-MS for the heavy-metal panel and microbiology on the same sample.

The amino acid composition is the practical blend test. Elastin is rich in glycine, alanine, proline and valine and low in polar residues; collagen carries hydroxyproline and hydroxylysine, which elastin does not. A hydroxyproline figure beside a low desmosine figure points to collagen or gelatin in the drum. Species identification is better done by PCR on the raw tissue than on the finished hydrolysate, where the DNA may no longer be amplifiable. Every screen should come with its detection limit; otherwise “not detected” describes the reach of the method, not the lot.

Chain of custody matters. The laboratory should test the retained sample and quote the lot number in its report.

Six lines to compare

The comparison needs six items: the species and tissue; the protein result with its factor and basis; the peptide content with its HPLC mode; the desmosine result with its method and basis; ash, moisture and particle size; and the allergen, TSE and origin statements.

Behind the certificate is a batch record: who ran the lot, which raw batch fed it, how it was hydrolysed and dried, and which sample was retained. The catalogue ranges are on the elastin peptides product page; the tests that support the desmosine line are on the identity page; the analytical methods are set out in the methods library; the quality page sets out the release route.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation