03 Stability

Flaxseed oil oxidises; the pack and the headspace set the retest period

Technical document 03 · Reviewed 2026-11-20 · Flaxseed Oil

On this page
  1. The neat oil in its sealed pack
  2. Blends, emulsions and softgel fills
  3. What moves the oil in storage
  4. A stability protocol for the oil
  5. What the finished formula does
  6. How the retest period is set

Flaxseed oil is among the most unsaturated of the common seed oils: ALA is 18 carbons with three double bonds, and linoleic acid adds two more. Oxygen attacks those bonds, light and warmth accelerate the attack, and the fatty-acid assay can still read inside its range while the oil turns. Stability is therefore read from peroxide value, anisidine value and free fatty acid over time, in the pack and at the temperature the customer will use.

In one line

The oil's double bonds are the whole stability story: oxygen, light and warmth shorten the induction period, and the pack can slow the reaction but cannot stop it.

The neat oil in its sealed pack

The catalog moisture limit is ≤0.1%. That is a gate at filling, not a buffer for a humid store: water drives hydrolysis, hydrolysis raises free fatty acid, and an open drum in a damp room is no longer in the condition it was tested in. The 1 kg amber bottle and the 25 kg HDPE drum both need a closed liner and a dry store.

Oxygen is the larger variable. Oxidation starts at the oil surface and continues in whatever air sits above it, so a full drum ages more slowly than one drawn down. A nitrogen blanket at filling displaces that air, but the flush has to be specified and checked. Once a pack is open, decant the remainder into a smaller container and use it within the agreed in-use period.

Light is the third variable, and amber glass is not decoration: an oil in a clear bottle on a lit shelf oxidises through the glass. Warmth accelerates the same reactions, so a store next to a heater is a different condition from a temperature-controlled room. The three factors compound, and a warm, bright, part-used bottle is the hardest case.

Blends, emulsions and softgel fills

Flaxseed oil is not water-soluble and is not supplied as an aqueous solution. The systems that matter are oil blends, oil-in-water emulsions and softgel fills, and each changes the rate at which oxygen reaches the oil.

In a blend, the least stable oil usually governs the induction period, so a small share of flaxseed oil can pull a mostly saturated blend down; measure the blend, not its components. In an emulsion the oil is dispersed into droplets, the interfacial area is large, and oxygen, light and trace metals meet the oil at the interface; the emulsifier, the pH and the antioxidant strategy outweigh the bulk oil's release result.

A softgel shell limits oxygen transfer without stopping it, and it can carry moisture into the fill. Measure the fill at release and at the end of the study, and watch the shell for discolouration and leakage. A powder is a different system: the starch wall protects most of the oil, but free oil at the surface is exposed and moisture is a failure route.

What moves the oil in storage

What changes flaxseed oil during storage
FactorEffectControl
OxygenRaises peroxide value, then the anisidine valueNitrogen blanket; low headspace; sealed pack
LightAccelerates oxidation at the oil surfaceAmber glass or an opaque secondary pack
HeatShortens the induction period; speeds hydrolysisCool store; short holds; no hot loading bay
MoistureDrives hydrolysis and raises free fatty acidDry store; closed liner; ≤0.1% at release
Trace metalsCatalyse oxidation at very low levelsStainless steel or glass contact; avoid iron and copper
Repeated openingReplaces the headspace with airSmaller packs; decant into a full container

The factors reinforce one another: a part-used drum in a warm room combines heat, oxygen and a large headspace, and the result is worse than the effects measured separately. The useful question is not whether the oil is stable in the abstract, but for how long, in which pack and condition.

A stability protocol for the oil

A usable protocol fixes four things: the container, the climate, the sampling times and the tests. A common design uses 25 °C/60% relative humidity for long-term storage, 30 °C/65% RH as an intermediate condition and 40 °C/75% RH for accelerated storage. Add a light-exposure arm, because a dark incubator cannot reveal a photochemical failure, and include the customer's pack.

Test peroxide value, anisidine value, free fatty acid, moisture and appearance at every point, and run the full fatty-acid profile at the first and last points to confirm that ALA and identity are unchanged. Tocopherols are worth measuring if the oil is sold on its minor fraction or if an antioxidant has been added. An induction period on a Rancimat or Oxipres instrument is a useful screen, but it ranks oils; it does not replace a storage study in the pack.

Sampling has to be representative. A top-of-drum sample is not the same as one drawn after mixing, and a sample left open on a bench has started to oxidise before it reaches the laboratory. The protocol should say how the sample was taken, stored and how long it waited.

What the finished formula does

A softgel is the usual format, and the fill is the part that fails. Shell thickness, the plasticiser and the seam decide how much oxygen and moisture reach the oil, and a fill can turn before the shell shows anything. Measure the fill's peroxide and anisidine values, not only the capsule's appearance.

An antioxidant can slow the reaction but cannot undo it. Mixed tocopherols, rosemary extract or another system should be named with its level in the specification, and adding tocopherol to an oil with a high peroxide value does not restore the specification. Decide the system before the stability study, not after a failing result, and check that the label reflects it.

An emulsion adds the aqueous phase, the interface and a pH to control, and a dry blend adds the carrier and the risk of moisture migration. A stick pack needs its own study; the bulk oil's data does not transfer to a powder or a beverage, and neither does the softgel's.

How the retest period is set

We do not publish one shelf-life number for flaxseed oil, because the pack, the headspace and the storage condition set it. The retest period is supported by data for the pack the customer buys; a figure quoted without that pack and condition is an assertion.

Before an extension, the retained sample is re-tested at the end of the period against the same limits: peroxide value, anisidine value, free fatty acid, moisture and appearance, with the profile checked at the end point. A bulk result does not transfer to a repacked bottle, a softgel or an emulsion. The documents should carry the lot, the production date and the retest date, and the buyer should confirm the remaining life on arrival.

The catalog specification is on the flaxseed oil product page. The release tests are set out on the COA page, the packs and lead time are on the MOQ page, the test methods are indexed under analytical methods, and the release and retained-sample workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation