02 Grade and form

Retinol or a retinyl ester: choosing a vitamin A grade

Technical document 02 · Reviewed 2026-11-20 · Retinol

On this page
  1. Why the form is the first line of the specification
  2. The three materials side by side
  3. Oil phase against powder
  4. Dose arithmetic and the label
  5. What to write into the specification
  6. When the ester is the better purchase

Retinol is the free alcohol of vitamin A; retinyl palmitate and retinyl acetate are esters of that alcohol with a fatty acid. The catalog form here is a ≥95.0% oil, while the two esters are sold as spray-dried powders at 1.0–1.1 MIU/g and 500,000 IU/g. The choice changes the potency per gram, the physical form, the oxidation behaviour and the ingredient name on the label.

In one line

The grade decision is not a potency step: the free alcohol and the esters are different materials with different stability, physical form and label names.

Why the form is the first line of the specification

A specification that says “vitamin A” and stops there has not identified a material. Three commercial products answer to that name, and they differ in molecular mass, in stability and in the word that must appear on the label. Retinol is the parent alcohol; esterification attaches palmitic or acetic acid to the hydroxyl group, which raises the molecular mass and lowers the vitamin A content per gram. The ester is not a diluted retinol but a different molecule with its own CAS number and its own certificate.

The free alcohol is the form the IU arithmetic is written around: one microgram of all-trans-retinol is 3.33 IU. The esters are converted back to retinol for that calculation, which is why an ester certificate can quote a retinol equivalent as well as its own mass. The conversion is chemistry, not a marketing allowance.

The three materials side by side

Retinol and the two retinyl esters · identity and potency
PropertyRetinolRetinyl palmitateRetinyl acetate
CAS68-26-879-81-2127-47-9
Formula and massC20H30O · 286.45 g/molC36H60O2 · 524.86 g/molC22H32O2 · 328.49 g/mol
Retinol per gram of pure material1,000 mgAbout 546 mgAbout 872 mg
Pure material potencyAbout 3.33 million IU/gAbout 1.82 million IU/gAbout 2.90 million IU/g
Catalog presentation here≥95.0% oil1.0–1.1 MIU/g powder500,000 IU/g powder
Behaviour in airThe most readily oxidised of the threeMore resistant, but hydrolyses to retinolMore resistant, but hydrolyses to retinol
Label nameRetinolRetinyl palmitateRetinyl acetate

The potency column explains why a gram-for-gram swap fails. One gram of the 95% oil carries about 3.16 million IU; one gram of the 1.0 MIU/g palmitate powder carries one million IU. Replacing one with the other at the same weight changes the dose by a factor of about three.

Oil phase against powder

Retinol is insoluble in water and soluble in fats and organic solvents, so it belongs in the oil phase: a softgel fill, an oil blend, or the dispersed phase of an emulsion. It is weighed as an oil, protected from light while the batch is open, and kept under nitrogen where the process allows. The catalog appearance is a yellow to amber, clear to slightly viscous oil, and the colour deepens as the material ages.

The ester powders work the other way. A spray-dried palmitate or acetate is a light yellow powder that disperses in warm water, flows in a blender and can be compressed into a tablet. It is weighed as a solid, blended with the other powders and packed in a foil pouch. The two presentations do not share a weighing room, a dosing line or a stability file.

Between the two extremes sit the formulated options: an oil dilution of retinol in a carrier oil, and a retinol powder on a carrier, which the catalog lists on request. Each of those is a new specification with a declared carrier, not a packing variant of the oil.

Dose arithmetic and the label

At ≥95.0% assay, one gram of oil contains 950 mg of retinol, which is 950,000 µg and about 3.16 million IU. A 500 µg retinol-equivalent dose therefore weighs about 0.53 mg of oil. No softgel line weighs half a milligram per capsule, so the oil is diluted into a carrier oil and the dilution is specified and declared. The same arithmetic in reverse tells a buyer what a dilution must contain to deliver the label dose.

The ester powders run at lower potency density. One gram of the 1.0 MIU/g palmitate powder carries 300,000 µg of retinol equivalent, so a 500 µg dose weighs about 1.67 mg of powder. That is why the powders are blended into a tablet granulation or a capsule fill rather than weighed one dose at a time.

Keep the label units straight. The EU declares vitamin A in µg RE, with one microgram of retinol equal to one microgram RE. The US declares µg RAE on the same 1:1 basis for preformed retinol. Older labels and some export markets still use IU, where one IU of retinol is 0.3 µg. A label that mixes IU and µg without the conversion is a labelling error waiting for a reviewer.

What to write into the specification

  • “Retinol, CAS 68-26-8, C20H30O, all-trans-retinol oil.”
  • “Assay ≥95.0% as-is by HPLC with UV detection; report the IU/g conversion.”
  • “Peroxide value ≤10.0 meq O₂/kg, with the test date.”
  • “Declared antioxidant and carrier, if either is present.”
  • “Amber bottle, nitrogen headspace, storage condition and retest period.”
  • “Destination market and label unit confirmed before the order.”

When the ester is the better purchase

Choose an ester when the dosage form is a tablet, a dry blend, a stick pack or a water-dispersible powder, and when the process applies heat that an oil would not survive. Choose the retinol oil when the formula is a softgel or an oil blend, when the label names retinol, and when the dose is small enough that a high-potency oil keeps the fill weight sensible.

A switch in either direction is a new specification, a new certificate and a new label. The stability file from one material does not carry to the other, because the degradation route changes with the form: the free alcohol oxidises directly, while an ester first hydrolyses and then exposes retinol.

The catalog specification sits on the retinol product page; the ester grades are on the vitamin A page; the detailed comparison is on the free alcohol versus ester page; the release tests are on the COA page; the handling conditions are on the stability page; and the identity checks are on the identity page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation