L-cysteine HCl, the free base or L-cystine: choosing a form
L-cysteine is sold as the hydrochloride monohydrate, the anhydrous hydrochloride, the free base and the disulfide L-cystine. The four differ in cysteine content, pH, solubility and label name, and the hydrochloride carries its own hydrate question. The catalog form here is the monohydrate at 80 mesh.
The hydrochloride, the free base and L-cystine are different label ingredients, and the hydrate question sits inside the hydrochloride itself.
Why the hydrochloride is a separate ingredient
L-cysteine has a thiol, an amino group and a carboxyl group. The hydrochloride forms at the amino group, so the molecule arrives as a salt with one molecule of hydrogen chloride and, in the catalog form, one molecule of water. That is a different chemical entity from the free amino acid, with a different CAS number, a different mass and a different label name.
The salt is not a stronger grade of cysteine. It is 69.0% cysteine by mass in the monohydrate, so a formula that counts the salt as cysteine overstates the cysteine by 45%. The salt dissolves freely and gives a strongly acidic solution; the free base is closer to neutral, and L-cystine, the disulfide dimer, is poorly soluble. A mesh is a grade; a salt is a molecule.
The four forms side by side
| Form | CAS · formula · MW | Cysteine content | Solution and label |
|---|---|---|---|
| L-cysteine HCl monohydrate | 7048-04-6 · C3H7NO2S·HCl·H2O · 175.64 | 69.0% | Freely soluble; about pH 1.5–2.0 at 5%; label: L-cysteine hydrochloride monohydrate |
| L-cysteine HCl anhydrous | 52-89-1 · C3H7NO2S·HCl · 157.62 | 76.9% | Freely soluble; strongly acidic; label: L-cysteine hydrochloride |
| L-cysteine | 52-90-4 · C3H7NO2S · 121.16 | 100% | Soluble; near-neutral; label: L-cysteine |
| L-cystine | 56-89-3 · C6H12N2O4S2 · 240.30 | Two cysteine units | Poorly soluble, about 0.1 g/L; label: L-cystine |
The percentages are not directly comparable. An assay of 99.0–101.0% for the hydrochloride describes the salt, not the cysteine in it; the free base and the cystine are assayed against their own references. Read the named form and the basis before comparing two certificate figures, because 99% of a salt and 99% of the free amino acid are different quantities of cysteine.
The label follows the form, not the assay. A hydrochloride lot cannot fill a claim written for L-cysteine, and a cystine lot cannot fill either. The names are close enough to be confused in a purchase order and far enough apart to make the finished label wrong.
Particle, water and the hydrate
Within the hydrochloride, the grade is physical. The catalog is an 80 mesh powder: ≥95% through 80 mesh. A granulated lot is available on request and changes flow, dust and blend behaviour, not the chemistry. The mesh belongs on the purchase order and on the specification, because a mill or sieve change moves the result without moving the assay.
The powder is hygroscopic, has an intrinsic sulfur odour and ranges from white to off-white. The monohydrate holds water of crystallisation, which is part of its identity; the anhydrous salt is a different CAS and a different specification, not a drying step added to the same order. Loss on drying is set at ≤0.5% in the catalog, and the certificate should state whether that figure is free moisture or total water. The COA page sets out the water and chloride checks that settle the question.
Chloride is the other physical marker: about 20.2% in the monohydrate and 22.5% in the anhydrous salt. It is not on the release table, but it is the quickest analytical way to tell which hydrate a lot is, and a low figure is a warning that the lot is partly free base or diluted.
The dosage form narrows the choice
Capsules and tablets take the 80 mesh powder. A granulated lot flows better on a high-speed press, while the finer powder blends more evenly at low dose. The thiol odour is part of the material, so a closed capsule wall does work that a stick pack does not, and the hygroscopic powder needs a pack that keeps moisture out between filling and use.
Powder blends and drink mixes put solubility and pH first. The hydrochloride dissolves freely but gives an acidic solution, which can be acceptable in a fruit-flavoured mix and awkward in a neutral formula. The free base is closer to neutral but is a different label ingredient; L-cystine is too poorly soluble for a clear drink. The matrix decides whether the salt fits, and the label decides whether it is allowed.
Mass conversion is where the forms separate at the balance. A 500 mg claim for cysteine base needs 500 ÷ 0.690 = 725 mg of the monohydrate, or 650 mg of the anhydrous salt. A 500 mg claim for L-cysteine hydrochloride is a claim on the salt and is weighed as the salt. The panel and the weigh-up have to name the same form, or the formula is short or over by the water and the chloride.
What to write into the specification
- “L-cysteine hydrochloride monohydrate, CAS 7048-04-6, C3H7NO2S·HCl·H2O.”
- “Assay 99.0–101.0% by titration, with the basis stated.”
- “Specific rotation +6.0° to +7.5° (c=2, 5 M HCl), with temperature and path length.”
- “Chloride about 20.2% and water about 10.3% where the monohydrate is to be confirmed.”
- “Loss on drying ≤0.5%, with the water method named; ≥95% through 80 mesh.”
- “Heavy metals and microbiology as listed; source route and label name declared.”
Name the hydrate in the same line as the salt. “L-cysteine HCl” leaves the water open, and the water changes the cysteine content, the chloride figure and the mass at the balance. The specification should read as one form, one CAS and one set of numbers.
When not to switch
Do not switch forms to close an assay gap. If two certificates differ by a percentage point, check the basis, the hydrate and the method before changing the molecule. Do not move a printed label from one form to another; the ingredient declaration is part of the product. Do not use L-cystine where solubility is the limiting property, and do not use the hydrochloride where the acidity or the chloride load is the problem, whatever the assay says.
The comparison with the acetylated form is on the L-cysteine HCl versus NAC page. The product hub carries the catalog specification; the N-acetyl-L-cysteine page shows the other thiol ingredient in the range; the compliance page covers the market routes.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation